Learn with steem || Tutorial class 2 || Mechanical Engineering|| Topic- Rolling process || 25 % beneficiary set to Null

in India Speaks2 years ago (edited)

WhatsApp Image 2022-05-27 at 9.46.37 PM.jpeg

Source:CANVAS

Namaste Steemit,

Hello friends, how are you all, hope all is well, today I am going to write my second post about my in front of you subject. Now todays post is based on my previous post so before start to read my post please check my previous post. Link is given at the end of my post.

ROLLING

Blue Simple Process Flow Chart Graph.jpg

source

Definition- The process of plastically deforming metal bypassing it between rolls it's called or rolling process.

  • Most widely used, high production rate and closed tolerance.
  • The Friction between the rolls and the metal surface produces a high compressive stress.
  • Hot working (unless mentioned cold rolling)
  • Metal will undergo bi axial compression.

R.png

Source:

Hot Rolling

bloom-1568604_1920.jpg

Forming Bloom

  • Done above the recrystallization temperature.
  • Results in fine grain structure.
  • In hot rolling the surface quality and final dimensions are very less accurate.
  • Breakdown of ingots into blooms or billets is done by hot rolling.

This is followed by further hot- rolling into plate, sheet, rod, bar, pipe and rail.

  • Hot rolling is terminated when the temperature falls to about 50 to 100 degree Celsius above the recrystallization temperature.
COLD ROLLING
  • Done below the recrystallization temperature.
  • Products are sheet, strip, foil etc. With good surface finish and increase mechanical strength with close product dimensions.
  • Performed on four- high or cluster type rolling mills because it generate high force and power.
Lubrication for rolling
  • In Hot rolling of ferrous metal is done without a lubricant.
  • Hot rolling of non- ferrous metal of wide variety of compounded oil and use emulsions and fatty acids
  • Generally Cold rolling lubricants are water soluble oils, low- viscosity lubricants such as mineral oils, emulsions paraffin and fatty acids.

HOT vs COLD ROLLING OF METALS

Hot RollingCold Rolling
Generally Metal is fed to the rules after being heated above the recrystallization temp.In this case Metal is fed to the rules when it is below its recrystallization temp.
The Rolled metal does not show work hardening effect.After being cold rolled the metal shows the work hardening effect
You can see the heavy reduction in the workpiece.Heavy reduction is not possible in this case.
Mechanical properties is improved.In this case Hardness increases excessive cold working generates cracks.
Blow holes and other similar defect present in the ingot are removed.Ductility of the metal reduces.
Due to hot rolling very thin sections are not obtained . Hot rolling of sheets less than 1.2 mm in thickness is not econ.Cold rolling increases the tensile strength and yield strength of steel metal.
The hot rolling is widely used in ferrous as well as non ferrous industry for steels, aluminium, copper, brass, bronze, magnesium, Nikhil and zinc alloy to change ingot into billets, slabs, sheets, bars, rods, wires and tubular shapes.Aluminium foil as thin as 0.020 mm can be made.
The hot roll surface finish is not good.The cold roll surface is smooth and free from oxide.

I hope you liked this tutorial series of mechanical engineering subject and please tell me in the comments, what you liked in this tutorial.

Note- First you read my previous post Link

Beneficiaries of this post:

@steemindiaa: 10%
@null: 25%

Sort:  

Thank you for contributing to #LearnWithSteem theme. This post has been upvoted by @fabio2614 using @steemcurator09 account. We encourage you to keep publishing quality and original content in the Steemit ecosystem to earn support for your content.

Club Status: #Club100

Sevengers Comment GIF.gif

Regards,
Team #Sevengers

after reading your tutorial post i know something about rolling in manufacturing process.

aapki diary se hum kuch na kuch accha hi sikhtai hai.

Your post admire me to learn about mechanical engineering and by reading your previous post i got intrest in this field.
Keep posting your tutorial post.

You are doing a great work on steemit platform . Thanks for sharing such a wonderful tutorial post.

 2 years ago 

knowlegeble post written by you. Keep posting bro.

Nice informative post!👍

I think you are a good teacher 😉

nyc post brother and the content is very useful for preparation candidates